free form logo

How Do You Calculate Cycle Time in Injection Molding? Formula, Worked Example, and Ways to Cut It

Most of every molding cycle is spent waiting. After the mold fills, the part has to cool before it can come out. Industry sources put cooling at about half to 80% of the total cycle.

That waiting time shows up in your part price. In plastic injection molding, cycle time decides how many parts a press makes each hour. Cutting even a few seconds per cycle adds up over a long production run.

This guide shows you how to calculate cycle time in injection molding. We’ll give you a simple formula and walk through one worked example. A good estimate helps you check a quote, plan your production volume, and spot design changes that save time.

How Do I Calculate the Cycle Time for Injection Molding?

To calculate injection molding cycle time, add up the time for each step in one cycle:

Cycle time = fill time + pack/hold time + cooling time + mold open, eject, and close time

  1. Fill: The time it takes to inject plastic into the mold. This is usually a few seconds.
  2. Pack/hold: The time pressure is held while the gate freezes.
  3. Cooling: Usually the longest step. It depends mostly on wall thickness. Doubling the wall roughly quadruples cooling time.
  4. Mold open, eject, and close: The machine motion between parts.

Most cycles take anywhere from a few seconds to about two minutes. To find parts per hour, divide 3,600 by your cycle time. Then multiply by the number of cavities in the mold.

What Makes Up One Injection Molding Cycle?

One cycle runs from the start of one shot to the start of the next. Every second in between counts toward your cycle time. Each cycle has four main steps.

StepWhat happensShare of the cycle
FillThe press injects molten plastic into the mold.Small, often just a few seconds
Pack/holdThe press holds pressure while the gate freezes.Short, depends on wall thickness and gate size
CoolingThe part cools in the closed mold until it’s solid enough to eject.Largest, about half to 80%
Mold open, eject, and closeThe mold opens, pushes the part out, and closes again.Short, depends on press speed and part size

Cooling takes the most time because plastic gives up heat slowly. That makes it the best place to look for time savings. For a closer look at what happens in each step, read our guide to the 4 stages of injection molding.

Now that you know what happens in each step, here’s how to put numbers on them.

The Cycle Time Formula, Step by Step

Start with the total formula from above. Add the time for fill, pack/hold, cooling, and mold motion. Three of those steps come from the press and the mold. Cooling takes a little math.

Most engineers use a standard equation to estimate cooling time:

Cooling time ≈ (s² ÷ (π² × a)) × ln[(4 ÷ π) × (Tm − Tw) ÷ (Te − Tw)]

Enter wall thickness in millimeters and thermal diffusivity in mm²/s. The answer comes out in seconds. “ln” is the natural log button on most calculators.

Here’s what each letter means in plain words:

SymbolWhat it meansWhere to find it
sWall thickness at the part’s thickest wallYour part drawing
aThermal diffusivity, or how fast heat moves through the plasticResin datasheet or material supplier
TmMelt temperature, or how hot the plastic is going inResin datasheet
TwMold temperature, or how warm the mold steel is keptResin datasheet (recommended range)
TeEjection temperature, or how cool the part must be before it comes outOften the heat deflection temperature (HDT) on the resin datasheet

Look at the “s²” in the equation. Wall thickness is squared, so it has the biggest effect on cooling time. If you double the wall, cooling takes about four times as long.

Most datasheets don’t list thermal diffusivity. You can work it out by dividing thermal conductivity by density times specific heat. Your material supplier can give you any values that are missing.

Fill, pack/hold, and mold motion times depend on the press and the mold. They are set on the press and confirmed during T1 and T2 mold trials. Add them to your cooling time to get the full cycle.

A formula is easier to follow with real numbers. Let’s run one.

Worked Example: Cycle Time for a Simple Part

Let’s run the numbers for a simple ABS part. It has a 2.5 mm wall and runs in a 4-cavity mold. We’ll use these values for the cooling equation:

InputValue
Wall thickness (s)2.5 mm
Thermal diffusivity (a)0.11 mm²/s (typical ABS range is about 0.08–0.11)
Melt temperature (Tm)240°C (464°F)
Mold temperature (Tw)60°C (140°F)
Ejection temperature (Te)83°C (181°F)

First, work out the cooling time one piece at a time:

  1. Square the wall: 2.5 × 2.5 = 6.25
  2. Multiply π² by diffusivity: 9.87 × 0.11 = 1.086
  3. Divide: 6.25 ÷ 1.086 = 5.76
  4. Find the temperature ratio: (240 − 60) ÷ (83 − 60) = 180 ÷ 23 = 7.83
  5. Multiply by 4 ÷ π (about 1.273): 7.83 × 1.273 = 9.97
  6. Take the natural log: ln(9.97) = 2.30
  7. Multiply: 5.76 × 2.30 = about 13.2 seconds of cooling

Next, add the other steps. For this example, we’ll pick times that fall inside typical published ranges:

StepExample timeTypical range
Fill1.5 seconds0.5–5 seconds
Pack/hold4 seconds2–15 seconds
Cooling13.2 secondsFrom the equation
Mold open, eject, and close5 seconds2–10 seconds
Total cycle timeabout 24 seconds
Shots per hour3,600 ÷ 24 = 150
Parts per hour (4 cavities)150 × 4 = 600

Cooling is more than half of this cycle. That’s why wall thickness and mold cooling matter so much.

How does that compare with a real part? RJG, an injection molding training and technology company, published a test on an ABS tensile bar about 3.3 mm thick. Its full cycle ran 21.43 seconds, with 10 seconds of cooling and 8 seconds of pack/hold. That total is close to our example, but real numbers always shift once the mold runs on the press.

Once you know your parts per hour, you can estimate your price.

What Is a Typical Injection Molding Cycle Time?

Most injection molding cycles take anywhere from a few seconds to about two minutes. Where your part lands depends mostly on wall thickness, size, and material.

Part typeExamplesTypical cycle time
Thin-wall, high-volume partsPackaging, caps, closures2–10 seconds
General engineering partsEnclosures, brackets, housings15–45 seconds
Thick or large structural partsAutomotive and industrial parts60–120+ seconds

Be careful with any single “average” cycle time. Two parts of the same size can run very differently if one has thicker walls. A 4 mm wall takes about four times as long to cool as a 2 mm wall. Only your own part’s numbers tell you what your cycle will be.

Your number will differ from the example. Here’s why.

What Changes Your Cycle Time?

Several things push your cycle time up or down. Some come from the part design. Others come from the mold and the press.

  • Wall thickness: Cooling time grows with the square of the wall, so a small cut in thickness saves a lot of time.
  • Material: Plastics move heat at different rates, so some cool faster than others at the same thickness.
  • Crystalline vs. amorphous resins: Semi-crystalline plastics like nylon must form crystals to get stiff, while amorphous plastics like ABS stiffen as they cool.
  • Mold cooling design: Cooling channels placed close to the part pull heat out faster and more evenly.
  • Mold temperature: A cooler mold speeds up cooling, but too cool can hurt surface finish.
  • Runner system: A cold runner has to cool along with the part, while a hot runner keeps plastic melted inside the mold.
  • Part size: Larger parts often need larger presses, which take longer to open, close, and fill.
  • Ejection and part removal: Parts that release cleanly and fast, steady part removal both trim time between shots.

Your press also needs to be the right size for the job.

How to Reduce Cycle Time Without Hurting Part Quality

The fastest cycle is not always the best cycle. The goal is to cut time while every part still meets spec. These changes give you the most room to do that.

  • Use thinner, more even walls. Thick spots set the cooling time for the whole part. A design for manufacturability (DFM) review can catch them before the mold is built.
  • Improve the cooling channels. Channels that follow the shape of the part, called conformal cooling, pull heat out faster and more evenly. In one published case study on a hard-to-cool part, conformal cooling cut cooling and cycle time by more than half. Even cooling also helps parts stay flat.
  • Switch to a hot runner. A hot runner removes the cold runner that has to cool with each shot. It costs more up front but can pay off at high volumes.
  • Tune the process settings. Fill speed, pack time, and cooling time can often be trimmed once the mold is running. Small changes, tested one at a time, add up.

Watch out for cutting cooling time too far. A part that comes out before it’s rigid can warp. Rushed cooling around thick sections can also leave sink marks. A few extra seconds of cooling costs less than a bin of scrap.

Getting an Accurate Cycle Time Estimate at Freeform Polymers

The formula gives you a solid starting point. Real numbers come from mold sampling and testing, when the mold runs and the process is dialed in.

Cycle time has the biggest total impact in high-volume production. A few seconds per shot turns into hours of press time over a long run. That time shows up in your part price.

Founded in 2011, Freeform Polymers is an ISO 9001:2015 certified shop serving businesses across Utah and the surrounding areas. Our team builds molds and runs production, so we can talk through your part with you.

Want a real number for your part? Call us at (435) 774-9090 or contact us today to get started!